KYOCERA S-9100DN User Manual Page 63
- Page / 143
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 3 Using the Operator Panel
3-47
Press the
ENTER
key. A question mark (?) appears.
Press the ENTER key. All the customized paper weight
and duplex path settings will be reset to the default.
The message display returns to Ready.
Verifying the Total Printed Pages and Resetting the Ton-
er Counter
You can display the total number of pages printed by your print-
er for confirmation whenever necessary. The total number of
printed pages can also be checked on the status page. More-
over, for proper maintenance scheduling, it will be necessary to
reset the toner counter using this menu each time a new toner
container is installed.
Verifying the Total Printed Pages
This procedure only displays the total number of printed pages.
The number cannot be changed.
Press the
MENU
key.
Press the 3 or 4 key repeatedly until Life
Counters > appears.
Press the 2 key.
Press the 3 or 4 key until >Total Print appears.
Press the MENU key. The message display returns to
Ready.
Resetting the Remaining Toner Counter
When the toner container is replaced, reset the toner counter as
follows so that an accurate toner gauge measurement is indi-
cated on the status page. Note that if this operation is per-
formed when the toner container is not replaced, the toner
gauge measurement will not be indicated correctly. Also refer to
the Installation Guide supplied with the toner kit when replacing
the toner container.
Press the MENU key.
Press the 3 or 4 key repeatedly until Life
Counters > appears.
Press the 2 key.
Press the 3 or 4 key repeatedly until >New Toner
Installed appears
Press the
ENTER
key. A question mark (?) appears.
Press the ENTER key. The toner counter is reset.
Press the MENU key. The message display returns to
Ready.
2.2.13 Other Modes
The modes described in the following pages can be accessed in
the Others submenu. To enter the Others submenu, press the
2 key while Others > is displayed.
The following submenus can be displayed by pressing the 2
key and then the 3 or 4 key.
• Message Language Selecting
• Automatic Form Feed Timeout Setting
• Sleep Timer Setting
• Received Data Dumping
• Printer Resetting
• Resource Setting
• Alarm (Buzzer) Setting
• Auto Continue Setting
• Service Menu (for service personnel)
Message Language Selecting
You can select the language of the messages on the message
display by following the procedure given below.
Press the MENU key.
>Reset Type
Adjust ?
Life Counters >
>Total Print
0123456
5
6
1
2
3
4
5
1
Life Counters >
>New Toner
Installed
>New Toner
Installed ?
2
3
4
5
6
7
1
- Operation Guide 1
- CONTENTS 6
- Introduction 7
- IMPORTANT! PLEASE READ FIRST 8
- Caution Labels 8
- Installation Precautions 9
- Precautions for Use 10
- Cautions for Toner Handling 11
- Chapter 1 Names of Parts 12
- Chapter 1 Names of Parts 13
- Chapter 2 How to Load Paper 14
- Chapter 2 How to Load Paper 15
- 1.3 Setting Envelopes 16
- DATA ATTENTION 17
- 1.1 Operation Indicators 18
- 1.2 Message Display 18
- 1.3 Interface Indicator 18
- 1.4 Paper Size Indicator 19
- 1.5 Paper Type Indicator 19
- 1.6 Keys 19
- 2. Using the Operator Panel 20
- 2.2.1 Printing the Menu Map 26
- 2.2.2 Printing Status Page 26
- 2.2.3 e-MPS 27
- PERMANENT CODE JOB LIST 31
- VIRTUAL MAIL BOX LIST 32
- 2.2.5 Changing the Emulation 38
- 2.2.7 Using Page Set Menus 42
- EcoPrint setting is Off 46
- (default) 46
- EcoPrint setting is On 46
- WRITE INFORMATION 48
- PARTITION LIST 49
- 2.2.10 Operating a RAM Disk 50
- FORMAT INFORMATION 55
- 2.2.12 Paper Handling 56
- 2.2.13 Other Modes 63
- FS-9500DN 68
- Chapter 4 Troubleshooting 69
- 2. Print Quality Problems 70
- Chapter 4 Troubleshooting 71
- 3. Indicators and Messages 72
- 3.3 Error Messages 74
- 4. Correcting a Paper Jam 76
- 4.1 Jam in Paper Cassette 77
- 4.2 Jam at the MP Tray 77
- 4.3 Jam in Left Cover 1 78
- 4.4 Jam in Left Cover 2 79
- Chapter 5 Paper Selection 80
- Chapter 5 Paper Selection 81
- 2. Special Paper 82
- 2.2 Adhesive-Backed Labels 83
- 3. Paper Type 84
- Chapter 6 Maintenance 85
- Chapter 6 Maintenance 86
- Appendix A Fonts 89
- Appendix A Fonts 90
- Board and DIMM 93
- 2. Installing DIMMs 94
- 1. Parallel Interface 95
- 2. Serial Interface 96
- 3. RS-232C Protocol 97
- 4. RS-232C Cable Connection 98
- Appendix D Option Units 100
- Appendix D Option Units 101
- 2. Installing Option Units 102
- 2.4 Hard Disk 103
- 2.5 Memory Card 103
- Appendix E Specifications 104
- Appendix E Specifications 105
- Glossary 106
- Kyocera Mita Corporation 110
- Printer Driver Guide 111
- Regarding Tradenames 112
- Kyocera 112
- Mita Digital Library CD-ROM 112
- Contents 113
- (DF-70/DF-71) 118
- 2.1.6 Using the RAM Disk 120
- 2.1.7 Selecting the User Name 121
- Language 122
- 3.1 Setting the Paper Size 124
- 3.1.1 Custom Size Settings 126
- 3.1.2 Advanced Media Settings 127
- 3.3 Using the Booklet Mode 129
- 3.6 e-MPS 132
- 3.6.1 Using Job Retention 133
- 3.6.3 Using Code Job 141
Related products and manuals for Copiers KYOCERA S-9100DN
Copiers KYOCERA KM-1820 User Manual
(1 pages)
(1 pages)
Copiers KYOCERA KM-C830D User Manual
(161 pages)
(161 pages)
Copiers KYOCERA All Pinters User Manual
(58 pages)
(58 pages)
Copiers KYOCERA 1500 User Manual
(92 pages)
(92 pages)
Copiers KYOCERA KM-1820 User Manual
(147 pages)
(147 pages)
Copiers KYOCERA FS 9530DN User Manual
(172 pages)
(172 pages)
Copiers KYOCERA KM-4050 User Manual
(1 pages)
(1 pages)
Copiers KYOCERA FS-680 User Manual
(141 pages)
(141 pages)
Copiers KYOCERA FS-3820N User Manual
(227 pages)
(227 pages)
Copiers KYOCERA KM-1810 Datasheet
(4 pages)
(4 pages)
Copiers Kyocera CUA 25307 User Manual
(87 pages)
(87 pages)
© 2020, manymanuals.com. All rights reserved. | 1.650 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals