KYOCERA S-9100DN User Manual Page 42
- Page / 143
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 3 Using the Operator Panel
3-26
Press the 3 or 4 key repeatedly until >Pitch ap-
pears.
Press the ENTER key. A blinking cursor ( _ ) appears.
Press the 3 or 4 key to increase or decrease the value
of the figure where the cursor is blinking. The character
pitch can be set between 0.44 and 99.99 characters
per inch, in 0.01 character-per-inch increments. You
can use the 2 and 1 keys to move the cursor right and
left.
When the desired size is displayed, press the ENTER
key.
Press the MENU key. The message display returns to
Ready.
Printing a List of Fonts
To help in selecting fonts, you can print a list of the fonts includ-
ing option fonts.
Press the MENU key.
Press the 3 or 4 key repeatedly until Font > appears.
Press the 2 key.
Press the 3 or 4 key repeatedly until List of In-
ternal Fonts appears. List of Option Fonts
appears.
(Internal Fonts)
(Optional Fonts)
Press the
ENTER
key. A question mark (?) appears.
(Internal Fonts)
(Optional Fonts)
Press the ENTER key again. Processing appears,
then Ready. The printer prints a list of fonts with a short
sample and font ID (number) for each font.
List of Fonts
2.2.7 Using Page Set Menus
In Page Set menus, you can set the number of copies, the page
orientation, and other settings regarding pagination.
Setting the Number of Copies
You can set the number of copies of each page to be printed for
the current interface. The number of copies can be set between
1 and 999. The number of copies can be set whenever the mes-
sage display indicates Ready.
Press the MENU key.
>Pitch
10.00 cpi
>Pitch
10
.00 cpi
Font >
>List of
Internal Fonts
>List of
Option Fonts
5
6
7
8
9
1
2
3
4
>List of
Internal Fonts?
>List of
Option Fonts ?
5
6
Internal Scalable and Bitmapped Fonts List
Font Name Scalable/Bitmap Password Selection [FSET] Font ID
PRESCRIBE
Internal Scalable and Bitmapped Fonts List
Font Name Scalable/Bitmap Password Selection [FSET] Font ID
PRESCRIBE
1
- Operation Guide 1
- CONTENTS 6
- Introduction 7
- IMPORTANT! PLEASE READ FIRST 8
- Caution Labels 8
- Installation Precautions 9
- Precautions for Use 10
- Cautions for Toner Handling 11
- Chapter 1 Names of Parts 12
- Chapter 1 Names of Parts 13
- Chapter 2 How to Load Paper 14
- Chapter 2 How to Load Paper 15
- 1.3 Setting Envelopes 16
- DATA ATTENTION 17
- 1.1 Operation Indicators 18
- 1.2 Message Display 18
- 1.3 Interface Indicator 18
- 1.4 Paper Size Indicator 19
- 1.5 Paper Type Indicator 19
- 1.6 Keys 19
- 2. Using the Operator Panel 20
- 2.2.1 Printing the Menu Map 26
- 2.2.2 Printing Status Page 26
- 2.2.3 e-MPS 27
- PERMANENT CODE JOB LIST 31
- VIRTUAL MAIL BOX LIST 32
- 2.2.5 Changing the Emulation 38
- 2.2.7 Using Page Set Menus 42
- EcoPrint setting is Off 46
- (default) 46
- EcoPrint setting is On 46
- WRITE INFORMATION 48
- PARTITION LIST 49
- 2.2.10 Operating a RAM Disk 50
- FORMAT INFORMATION 55
- 2.2.12 Paper Handling 56
- 2.2.13 Other Modes 63
- FS-9500DN 68
- Chapter 4 Troubleshooting 69
- 2. Print Quality Problems 70
- Chapter 4 Troubleshooting 71
- 3. Indicators and Messages 72
- 3.3 Error Messages 74
- 4. Correcting a Paper Jam 76
- 4.1 Jam in Paper Cassette 77
- 4.2 Jam at the MP Tray 77
- 4.3 Jam in Left Cover 1 78
- 4.4 Jam in Left Cover 2 79
- Chapter 5 Paper Selection 80
- Chapter 5 Paper Selection 81
- 2. Special Paper 82
- 2.2 Adhesive-Backed Labels 83
- 3. Paper Type 84
- Chapter 6 Maintenance 85
- Chapter 6 Maintenance 86
- Appendix A Fonts 89
- Appendix A Fonts 90
- Board and DIMM 93
- 2. Installing DIMMs 94
- 1. Parallel Interface 95
- 2. Serial Interface 96
- 3. RS-232C Protocol 97
- 4. RS-232C Cable Connection 98
- Appendix D Option Units 100
- Appendix D Option Units 101
- 2. Installing Option Units 102
- 2.4 Hard Disk 103
- 2.5 Memory Card 103
- Appendix E Specifications 104
- Appendix E Specifications 105
- Glossary 106
- Kyocera Mita Corporation 110
- Printer Driver Guide 111
- Regarding Tradenames 112
- Kyocera 112
- Mita Digital Library CD-ROM 112
- Contents 113
- (DF-70/DF-71) 118
- 2.1.6 Using the RAM Disk 120
- 2.1.7 Selecting the User Name 121
- Language 122
- 3.1 Setting the Paper Size 124
- 3.1.1 Custom Size Settings 126
- 3.1.2 Advanced Media Settings 127
- 3.3 Using the Booklet Mode 129
- 3.6 e-MPS 132
- 3.6.1 Using Job Retention 133
- 3.6.3 Using Code Job 141
Related products and manuals for Copiers KYOCERA S-9100DN
Copiers KYOCERA KM-1820 User Manual
(1 pages)
(1 pages)
Copiers KYOCERA KM-C830D User Manual
(161 pages)
(161 pages)
Copiers KYOCERA All Pinters User Manual
(58 pages)
(58 pages)
Copiers KYOCERA 1500 User Manual
(92 pages)
(92 pages)
Copiers KYOCERA KM-1820 User Manual
(147 pages)
(147 pages)
Copiers KYOCERA FS 9530DN User Manual
(172 pages)
(172 pages)
Copiers KYOCERA KM-4050 User Manual
(1 pages)
(1 pages)
Copiers KYOCERA FS-680 User Manual
(141 pages)
(141 pages)
Copiers KYOCERA FS-3820N User Manual
(227 pages)
(227 pages)
Copiers KYOCERA KM-1810 Datasheet
(4 pages)
(4 pages)
Copiers Kyocera CUA 25307 User Manual
(87 pages)
(87 pages)
© 2020, manymanuals.com. All rights reserved. | 0.204 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals