KYOCERA 266ci User Manual Page 215
- Page / 260
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
HP 7550A Emulation [KC-GL] (Mode 8)
7-103
Figure 7. 29. KC-GL Sample Program
Plotter Status Information
When the RS-232C interface is used, in addition to receiving data, the plotter (printing
system) can return information such as the current pen position, pen status, and error
numbers. This return information applies to the following KC-GL instructions.
All of these instructions use the same syntax and must be followed immediately by a ter-
minator. They use no parameters.
The functions of these instructions appear on the following pages. The last ASCII char-
acter sent by the plotter (printing system) in response to the instruction is a terminator,
which will be designated here by the symbol TERM. The terminator is actually a car-
riage return unless changed by the ESC.M operator.
Instruction Description
OA Output Actual position and pen status
OC Output Commanded position and pen status
OE Output Error
OF Output Factors
OH Output Hard-clip limits
OI Output Identification
OL Output Label length
OO Output Options
OP Output P1 and P2
OS Output Status
OT Output carousel Type
OW Output Window
- Technical Reference 1
- General Infomation 3
- Introduction 5
- Conventions 6
- Table of Contents 7
- Barcodes 8
- Introduction to PRESCRIBE 9
- Entry and Exit 10
- Basic Concepts 12
- Format of PRESCRIBE Commands 12
- Landscape orientation 13
- Edge limits in HP emulation 13
- Portrait Orientation 13
- Page Orientation 14
- Print Direction 14
- Coordinate Systems 15
- Text Positioning 15
- Character Spacing 16
- Font height 17
- Baseline 17
- Command Parameters 18
- Character Strings 19
- Upper and Lowercase Letters 20
- Special Parameters 21
- ESC(11U 22
- Graphics Tutorial 23
- Standard Graphics 24
- Zero-relative Lines 25
- Relative Lines 26
- Lines in Terms of Angles 27
- Drawing Boxes and Circles 28
- Chapter 2 Graphics Tutorial 30
- Drawing Filled Shapes 31
- Drawing Filled Blocks 32
- Drawing Filled Arcs 33
- Defining Fill Patterns 34
- 32168421 32168421 8421 35
- 64 64 48 35
- Drawing Pie Charts 36
- Path Mode Graphics 38
- Drawing Lines 40
- Two Lines 41
- Line Ends 42
- Miter Limit 43
- Dash Type 44
- User Defined Dash Patterns 45
- Drawing Arcs and Curves 46
- Drawing Complex Curves 48
- Closed Paths 51
- Filled Areas 52
- Clipping Rectangle 54
- Raster Graphics 56
- Printing Raster Data 59
- × 16 dots) 61
- Chapter 3 63
- MCRO Command 64
- Examples of Macros 65
- Example 2 66
- Figure 3. 2. Macro Example 2 67
- Chapter 4 69
- Resident Fonts 70
- KPDL Fonts 72
- Substituting a Bitmap Font 74
- Font Selection 75
- Bitmap Font Mode 78
- Placement of Font Commands 79
- , x-offset 80
- Symbol Set 81
- International Characters 82
- Selecting HP Symbol Sets 82
- Linear Barcodes 86
- Two-dimensional Barcodes 94
- Overall Symbol Structure 95
- Functions of XBCP 96
- Positioning the Barcodes 97
- Macro PDF417 98
- Reference on the XBCP page 99
- Chapter 5 Barcodes 100
- Permanent Parameters 101
- FRPO Parameters 102
- Emulation 113
- Selecting an Emulation 114
- Automatic emulation sensing 115
- Chapter 7 Emulation 120
- IBM Symbol Sets 121
- Diablo 630 Control Codes 126
- Diablo 630 Emulation (Mode 2) 127
- Diablo 630 Symbol Sets 128
- Diablo Japan (285) 132
- EPSON LQ-850 Control Codes 136
- LQ-850 Symbol Sets 138
- LQ Germany (92) LQ U.K. (124) 139
- LQ Italy (220) LQ Spain (252) 140
- LQ Sweden (188) 144
- LaserJet Fonts 147
- LaserJet Symbol Sets 149
- Example: 151
- Resource Protection 152
- HP LaserJet Reset State 155
- LaserJet PJL 155
- PJL command syntax 156
- Rules for PJL Command Syntax 157
- PJL variables 158
- PJL Reset Status 159
- Table 7.23. PJL Reset Status 160
- E None 177
- PJL Syntax Comparison 179
- Greek-8 (8G) Math-8 (8M) 189
- PC-8 PC Nova (27Q) 208
- KC-GL Instruction Format 209
- KC-GL Environment Options 210
- Plot Coordinates (bit 0) 211
- Pen Selection 212
- Plotter Units and User Units 213
- Setting the Scaling Points 214
- Sample KC-GL Program 214
- Plotter Status Information 215
- LL, YLL, XUR, YUR TERM 216
- OI [Output Identification] 217
- OL [Output Label length] 217
- OO [Output Options] 217
- OP [Output P1 and P2] 217
- OS [Output Status] 218
- OT [Output carousel Type] 218
- Device-Control Instructions 219
- KC-GL Symbol Sets 221
- KC-GL Limits 223
- E-Mask Bit Values 225
- Default States (DF) 227
- Initial Conditions (IN) 227
- KPDL Operators 228
- KPDL Summary 229
- KPDL Status Operators 240
- KPDL User Parameters 247
- KPDL Page Device Parameters 248
- CollateDetails Parameters 251
- KPDL Error Messages 252
- KPDL Printable Area 253
- Figure 7. 52. Printable Area 254
- Rev. 4.9 2013.1 260
Related products and manuals for Multifunctionals KYOCERA 266ci
(36 pages)
Multifunctionals KYOCERA 221 SCAN Specifications
(115 pages)
(115 pages)
Multifunctionals KYOCERA 6550ci Manual
(82 pages)
(82 pages)
Multifunctionals KYOCERA 180 Specifications
(109 pages)
(109 pages)
Multifunctionals KYOCERA 250ci Specifications
(439 pages)
(439 pages)
Multifunctionals KYOCERA 221 Manual
(32 pages)
(32 pages)
(2 pages)
(36 pages)
Multifunctionals KYOCERA 181 Manual
(33 pages)
(33 pages)
Multifunctionals KYOCERA 300i Specifications
(225 pages)
(225 pages)
© 2020, manymanuals.com. All rights reserved. | 0.596 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals