KYOCERA FS-1300D User Manual Page 259
- Page / 410
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
RWER W
249
RWER W — [Read/Write External Resource] Write
data to external media
Format
RWER W, medium, data-type[, ’partition-name’];
Parameters
medium:
0 = hard disk or RAM disk
A = memory card
data-type:
1 = Font data
2 = Printable data
16 = Macro data
112 = File data
128 = API data (downloadable program)
partition-name:
Name of partition to which data is written, in a maximum of 15 printable ASCII
characters. If this parameter is omitted the printing system will automatically determine
the partition name.
Function
The RWER W command writes data to any external media whether it is a memory card
or the hard disk.
Although all data types may be written up to the amount allowed by the storage size of
the given media, note carefully that writing beyond this limit will result in data being
interpreted as unneeded.
Even if data is written to a device using the same file name, that data will be written
without overwriting the original file. A partition list will be printed as a warning when
this happens.
A command error results and the command has no effect if parameters other than the
above are used.
This command causes a page break and prints a write information page when executed.
The following example demonstrates how to send data from the computer to a memory
card. Typically, partition names should be specified when writing to the card. If omitted,
the partition names will be assigned automatically as follows:
DataS001, DataS002 ... DataSnnn.
Writing data to a memory card:
To write the contents of file DATA123.DOC to partition DATA123 on the memory card:
- Command Reference 1
- Table of Contents 5
- Contents—ii 6
- Contents—iii 7
- Contents—iv 8
- Index Index - 1 9
- Contents—vi 10
- PRESCRIBE Command Reference 11
- Access Commands 12
- Commands 13
- Text Spacing Commands 14
- Font Commands 14
- Cursor Movement Commands 15
- Vector Graphics Commands 15
- Path Mode Graphics Commands 16
- Raster Graphics Commands 17
- Color Commands 17
- Barcode Commands 18
- Macro Commands 18
- Debug Commands 19
- 2. PRESCRIBE Commands 21
- ACLI — Add CoLor by Index 22
- AMCR — call Automatic MaCRo 35
- Assign Paper Source Group 37
- ARC — draw filled-in ARC 38
- ASTK — Assign STacKer trays 42
- BARC — draw BARCode 44
- BLK — draw filled-in BLocK 50
- BOX — draw BOX 52
- CALL — CALL macro 54
- CCPY — Carbon CoPY 56
- File !R! 57
- CDSK — Check hard DiSK 59
- Configure color-Image Data 60
- CIR — draw CIRcle 62
- CLIP — CLIP current path 64
- CLPR — CLiP Rectangular area 65
- CLSP — CLoSe Path 67
- CMNT — CoMmeNT 69
- CMOD — Color MODe 70
- COPY — set number of COPIES 71
- CPAL — Control PALette 73
- CPTH — Character PaTH 74
- CTXT — print Centered TeXT 79
- DAF — Delete All Fonts 81
- DAM — Delete All Macros 82
- Draw to Absolute Position 83
- DELF — DELete Font 85
- DELM — DELete Macro 86
- DPAT — select Dashed PATtern 88
- Draw to Relative Position 90
- File/Printout 94
- Function 100
- Parameter 101
- ENDC — END carbon Copy 102
- ENDD — END Dump 103
- ENDM — END Macro 104
- Printout 105
- Related Commands 105
- ENDR — END Raster data 106
- EPL — select EcoPrint Level 108
- EXIT from PRESCRIBE mode 109
- MP tray Feed DIRection 110
- FILL — FILL closed path 111
- FLAT — set FLATness 114
- FLST — print Font LiST 115
- Sample of Font List 116
- FOLD — FOLD printed pages 117
- FONT — change current FONT 118
- FPAT — generate Fill PATtern 120
- Printout (300 dpi) 121
- FRPO — Firmware RePrOgram 122
- Related Command 123
- FRPO INIT — FRPO-INITialize 124
- FSET 0p12h12v0s0b6T; 127
- FTMD — bitmap FonT MoDe 129
- GPAT — set Gray PATtern 132
- GRAY — represent GRAY 134
- GRRD — GRaphic data ReaD 135
- Printout 136
- HUE — adjust HUE 137
- InterNaTionaL characters 139
- Factory-set (default) value 140
- JOBD — JOB Deletion 142
- JOBL — print JOB List 144
- !R! JOBL 2; EXIT; 145
- JOBO — JOB Output 146
- Parameters 148
- JOBS — JOB Start 150
- Spooling to Virtual Mailbox 151
- JOBT — JOB Terminate 154
- LAPI — LoaD API Program 156
- LDFC — LoaD Font Character 157
- LDFN S — LoaD truetype FoNt 163
- LGHT — adjust LiGHTness 165
- Default contrast 166
- Contrast set to high 166
- Contrast set to low 166
- Move to Absolute Position 167
- MCLR — Match CoLoR 169
- MCRO — define MaCRO 170
- MID — Multi-tray ID 174
- MPSS — e-MPS Storage 175
- Move to Relative Position 176
- MTYP — select Media TYPe 181
- NEWP — start NEW Path 185
- PAGE — start new PAGE 188
- !R! PANT ’Cool Gray 1’; EXIT; 190
- PARC — in Path, draw ARC 191
- PAT — select fill PATtern 193
- Example: 195
- PDIR — set Print DIRection 199
- PELP — in Path, draw ELlipse 206
- PIE — draw PIE chart 208
- New cursor position 210
- Positive x axis 210
- Distance 210
- PNCH — PuNCH 216
- PSRC — select Paper SouRCe 222
- PXPL — PiXel PLacement 223
- PRESCRIBE start sequence 224
- RCLT — Rotated CoLlaTion 226
- RDMP — Received-data DuMP 227
- RES — RESet 229
- RESL — select RESoLution 231
- RGBL — control RGB Level 232
- RGST — offset ReGiSTration 234
- Return to Previous Code Set 235
- Return to Previous Font 236
- Return to Previous Position 239
- Return to Previous PaLette 241
- Return to Previous Unit 242
- RTTX — RoTate TeXt 243
- ReceiVe CoLor raster data 248
- RVRD — ReceiVe Raster Data 249
- Format external media 252
- High > Low 255
- TrueType font 256
- Terminate string 258
- SBM — Set Bottom Margin 273
- SCAP — Set line CAP 275
- SCCS — Save Current Code Set 277
- SCF — Save Current Font 279
- Save Current Graphics state 281
- SCOL — Select COLor 283
- SCP — Save Current Position 284
- Set Characters Per Inch 285
- SCPL — Save Current PaLette 287
- SCS — Set Character Spacing 290
- SCSZ — Set Custom paper SiZe 291
- SCU — Save Current Unit 292
- Related commands 293
- SDP — Store Dash Pattern 294
- SEM — Set Emulation Mode 296
- SETF — SET alternate Font 297
- Set bitmap Font Attributes 299
- Shear = -1 304
- Shear = 0 304
- Shear = 1 304
- SGPC — Set kcGl Pen Color 306
- SHMI — Set HMI 307
- SIMG — Set IMaGe model 308
- Set Image Refinement level 313
- SLJN — Set Line JoiN 314
- SLM — Set Left Margin 316
- SLPI — Set Lines Per Inch 318
- SLPP — Set Lines Per Page 319
- SLS — Set Line Spacing 321
- SMLT — Set Miter LimiT 322
- SMNT — Set MoNiTor simulation 324
- SPAL — Select PALette 326
- SPD — Set Pen Diameter 327
- SPL — Set Page Length 329
- SPO — Set Page Orientation 331
- SPSZ — Set Paper SiZe 333
- SPW — Set Page Width 335
- SRM — Set Right Margin 337
- SRO — Set Raster Options 339
- Portrait (SPO P;) 340
- Landscape (SPO L;) 340
- SROP — Set Raster OPeration 341
- SSTK — select Sorter STacKer 343
- STAK — select paper STAcKer 344
- STAT — STATus 345
- Sample Status Page 346
- STM — Set Top Margin 347
- STPC — set STaPle Counter 349
- STPL — STaPLe 350
- STR — SeT dot Resolution 352
- STRK — STRoKe current path 353
- Set UnderLine Parameters 355
- TATR — apply Tray ATtributes 357
- TEXT — print TEXT 358
- TPRS — Text PaRSing 360
- TRansparency Separate Mode 361
- Unit Of Measurement per dots 364
- VMAL — Virtual Mailbox ALias 366
- Virtual Mailbox Output Bin 367
- WIDE — set WIDE A4 mode 370
- WRED — WRite EnD 371
- Number of rows is set to 20 378
- Number of rows is normal 378
- Number of columns is normal 379
- XBCP 7 — determine bar height 382
- XBCP 9 — enable truncation 384
- XBCP 10 — enable file name 385
- XBCP 11 — enable block count 386
- XBCP 12 — enable time stamp 387
- XBCP 13 — enable sender ID 388
- XBCP 14 — enable addressee ID 389
- XBCP 15 — enable file size 390
- XBCP 16 — enable checksum 391
- Printout 1 397
- Printout 2 398
- Printout 3 399
- XBUF — define a BUFfer name 400
- 409
- Rev. 4.6 2008.6 410
Related products and manuals for Laser/LED printers KYOCERA FS-1300D
(96 pages)© 2020, manymanuals.com. All rights reserved. | 2.476 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals