KYOCERA FS-C5150DN Specifications Page 160
- Page / 197
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Troubleshooting
6-4
Faint or blurred printing Clean the LSU.
For details, refer to LSU (LSU cleaning mode setting) on page 4-88.
Make sure the paper type setting is correct the paper being used.
For details, refer to Paper Settings on page 4-29.
Conduct color calibration either by switching the printer off then on or using
the printer operation panel.
For details, refer to Color Calibration on page 4-79.
Try adjusting the color control settings using the printer driver.
Check the operation panel. If the Toner low C,M,Y,K message is
displayed with color description, install a new toner kit for the color. To
replace toner, refer to Toner Container Replacement on page 5-2.
Refresh drum.
For details, refer to Drum (Drum/Refresh mode setting) on page 4-88.
Run [MC] and decrease the adjustment value. Decrease the adjustment
value 1 level at a time from the current value. If there is no improvement
after the value is decreased by 1 level, decrease by 1 level again. If there
is still no improvement, return the setting to the original value.
For details, refer to MC (Main charger output setting) on page 4-89.
Grey background Conduct color calibration either by switching the printer off then on or using
the printer operation panel.
For details, refer to Color Calibration on page 4-79.
Dirt on the top edge or back of the paper Check the paper chute and the ramp.
Open the rear cover and check for toner on the paper ramp inside the
paper transfer unit. Clean the paper ramp using a soft, dry, lint-free cloth.
For details, refer to Cleaning the Paper Transfer Unit on page 5-8.
Offset occures. Refresh drum.
For details, refer to Drum (Drum/Refresh mode setting) on page 4-88.
Run [MC] and decrease the adjustment value. Decrease the adjustment
value 1 level at a time from the current value. If there is no improvement
after the value is decreased by 1 level, decrease by 1 level again. If there
is still no improvement, return the setting to the original value.
For details, refer to MC (Main charger output setting) on page 4-89.
Printed Results Corrective Action
- FS-1300D 1
- Introduction 2
- Contents 3
- Menu Map 5
- Settings 6
- Legal and Safety Information 9
- License Agreements 10
- Open SSLeay License 11
- Original SSLeay License 12
- Compliance and Conformity 14
- CDRH Regulations 15
- Statement 15
- Communications du Canada 15
- Paper Recycling 16
- Energy Star (ENERGY STAR 16
- ) Program 16
- Environment 18
- Cautions for Toner Handling 18
- About the Operation Guide 19
- Conventions 19
- 1 Machine Parts 21
- Internal Components 22
- Operation Panel 24
- 2 Printing Operation 25
- Printing Operation 26
- Printing a Status Page 27
- COMMAND CENTER 27
- Installing the Printer Driver 28
- Express Mode 29
- Printer Driver User 30
- Guide on the CD-ROM 30
- Status Monitor 35
- Status Monitor icon 36
- Status Monitor Settings 37
- 3 Handling Paper 41
- Recommended Paper 43
- Selecting the Right Paper 44
- Smoothness 45
- Basis Weight 45
- Thickness 45
- Moisture Content 46
- Paper Grain 46
- Other Paper Properties 46
- Handling Paper 47
- Special Paper 48
- Postcards 50
- Envelopes 50
- Thick Paper 51
- Colored Paper 52
- Preprinted Paper 52
- Recycled Paper 52
- Coated Paper 52
- Paper Type 53
- Loading Paper 54
- to avoid 56
- Incorrect 57
- 4 Using the Operation Panel 59
- Message Display 61
- Status Information 62
- Error Codes 62
- Indicators in Message Display 63
- Cancel Key 64
- MENU Key 64
- Arrow Keys 64
- Menu Selection System 66
- Setting a Mode Selection Menu 68
- Report Print 69
- Status Page 71
- Print Fonts List 73
- Print Hard Disk File List 73
- Print RAM Disk File List 73
- Print File (Printing a file) 74
- Copies (Number of copies) 75
- Custom Box) 76
- Job Retention 80
- Quick Copy (Using Quick Copy) 81
- Using Proof-and-Hold 82
- Job Box Configuration 84
- Paper Settings 87
- >MP Tray Type 88
- Paper Size Dial 89
- >>>Duplex Path 94
- ? Enable 94
- >Reset Type Adjust ? 94
- Print Settings 95
- Duplex (Duplex printing) 96
- Page Set (Setting pagination) 101
- Portrait Orientation 102
- Landscape Orientation 102
- Network (Network settings) 104
- TCP/IP (IPv6) (IPv6 settings) 108
- Using the Operation Panel 109
- >>DHCPv6 109
- Device Common > 110
- >Message Language 110
- ? English 110
- Timer (Timer setting) 117
- Security 120
- NetWare (NetWare setting) 122
- AppleTalk (AppleTalk setting) 123
- IPP (IPP setting) 123
- IPSec (IPSec setting) 126
- ID (Administrator ID input) 128
- Color Calibration 137
- 3 Press Z 141
- MH=00000 MV=0 143
- >>M 12345 3 143
- Restart Printer 144
- Service (for maintenance) 144
- Optional Functions 147
- 5 Maintenance 149
- General Information 150
- Toner Container Replacement 150
- Maintenance 151
- Toner Kits 151
- Top Cover 152
- (Top Tray) 152
- Plastic Bag 153
- Toner Feed Slot 153
- Replacing the Waste Toner Box 154
- New Waste 155
- Toner Box 155
- Cleaning the Printer 156
- 6 Troubleshooting 157
- General Guidelines 158
- Direction 159
- Refresh drum 160
- Troubleshooting 161
- Error Messages 162
- Storage Error Codes 166
- Clearing Paper Jams 167
- 2 Remove the jammed paper 168
- Paper Jam in Printer 169
- 3 Close the rear cover 171
- Appendix 173
- Interface 174
- USB Interface 174
- Network Interface 175
- About the Options 177
- Expansion Memory Modules 178
- PF-520, PF-530 Paper Feeder 180
- Interface Slot 181
- Activate applications 183
- Optional Paper 184
- Feeder PF-520/ 184
- Feeder PF-530 185
- Glossary 187
- Glossary-2 188
- Sleep mode 189
- Status page 189
- Subnet Mask 189
- USB (Universal Serial Bus) 189
- Glossary-4 190
- First Edition 2010.10 197
- 2KTKMEN000 197
© 2020, manymanuals.com. All rights reserved. | 1.524 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals