KYOCERA FS-3700 User Manual Page 86
- Page / 116
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Message Corrective Action
Mechanical error ( = , , , ...)—Call a service person. The printer does
not operate when a message beginning with
is displayed. The total number
of pages printed is also indicated.
Controller error ( = , , , ...)—Call a service person. The printer does
not operate when a message beginning with
is displayed. The total number
of pages printed is also indicated.
Error Messages
Table 5.3 Error Messages
Message Corrective Action
The total amount of data received by the printer exceeds the printer’s internal
memory. Try adding more memory (expansion RAM). Press the CONT key to
resume printing. You can abandon printing by the CANCEL key.
The data transferred to the printer was too complex to print on a page. Press
the CONT key to resume printing. (The page may break in some pages.)
You can abandon printing by the CANCEL key.
Note: After this message has been displayed, Page protect mode will be
On. To maintain optimum use of memory during printing, display
from the control panel, and re-select
.
See the last page in this manual.
The memory card is accidentally removed from the printer’s memory card slot
during reading. If you continue reading the memory card, insert the same
memory card into the slot again. The printer again reads it from the
beginning of the data.
Note: We recommend that you follow the reading procedure from the
beginning to ensure correct reading of the memory card.
You have inserted the wrong memory card when the
message was displayed. Remove the wrong memory card from the printer’s
memory card slot and insert the correct memory card. The printer again reads it
from the beginning of the data.
This message appears when the printer is in the ready state and the memory
card is not formatted, and therefore cannot be read or written. Follow the
procedure on Section 2.10. to format the card.
This message appears when the printer is in the ready state and the battery in
the memory card is low. You can still enter the memory card mode, but the
battery should be changed as soon as possible.
This message appears when the printer is in the ready state and the battery in
the memory card is dead, or there is no battery at all. It is not possible to use
the memory card mode until you insert a good battery in the card.
5.5. Indicators and Messages
5-9
- FS-1700/3700 1
- Introduction 10
- Software Features 11
- Guide to the Manual 12
- User’s Manual (on CD-ROM): 13
- Table of Contents 14
- SIMM Sockets 19
- SIMM to be used 20
- Installing and Removing SIMMs 21
- Testing the Expansion Memory 22
- FCC statement 25
- Interface connectors 26
- Safety information 26
- Ozone concentration 27
- IMPORTANT SAFEGUARDS 28
- ENERGY STAR 30
- Feed Selection 39
- On-line/Off-line Setting 39
- Abandoning a Printing Job 39
- Status Printout 40
- 2.2. Operating Procedures 41
- Form Feed 43
- Mode Select Menu 44
- 2.4. Sleep (Ecopower) Mode 46
- 2.5. KIR Level 47
- 2.6. Ecoprint mode 48
- 2.7. Resource Protection 49
- Alarm Frequency 50
- 2.10. Operating a Memory Card 52
- Writing Data to a Memory Card 53
- Others. Error information 54
- Formatting a Memory Card 55
- Printing a list of data names 56
- Chapter 3 57
- Bitmap fonts 58
- Scalable fonts 58
- 3.2. List of Fonts 59
- 3.2. List of Fonts 60
- 3.3. Symbol set 67
- 3.3. Symbol set 68
- Chapter 4 70
- Maintenance 70
- Supplying Toner 71
- Sealing Strip 72
- New Waste Toner Bottle 74
- 4.2. Cleaning 75
- Protective Bag 76
- Grid Cleaner 76
- Main Charger Unit 76
- Paper Feed Unit 77
- Chapter 5 78
- Troubleshooting 78
- 5.2. Power Problems 79
- 5.3. Interface Problems 79
- 5.4. Print Quality Problems 80
- Faint or blurred printing 82
- Grey background 82
- Characters out of position 83
- 5.5. Indicators and Messages 84
- Maintenance Messages 85
- Error Messages 86
- 5.5. Indicators and Messages 87
- 5.6. Correcting a Paper Jam 88
- 5.6. Correcting a Paper Jam 89
- Mode Select Menu 90
- Appendix A 92
- Printer Specifications 92
- Appendix B 94
- Paper Selection 94
- Paper Specifications 95
- B.3. Special Paper 98
- Adhesive-Backed Labels 99
- Appendix C 101
- Host Computer Interface 101
- Interface Signals 102
- C.1. Parallel Interface 104
- RS-232C interface 105
- RS-422A interface 106
- Power OFF ( ) 107
- Jumper Connector 107
- C.3. RS-232C/RS-422A Protocol 110
- PRESCRIBE II FRPO D0 command 111
- C.4. RS-232C Cable Connection 112
Related products and manuals for Laser/LED printers KYOCERA FS-3700
(4 pages)
(2 pages)
(23 pages)
© 2020, manymanuals.com. All rights reserved. | 0.962 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals